CATIAPart Design Advanced презентация

CATIA Part Design Advanced

Course Presentation Objectives of the course In this course you will complete the knowledge acquired in the CATIA Part Design Fundamentals course Targeted audience New CATIA V5 users Prerequisites CATIA Part Design Fundamentals course

Table of Contents (1/2) Advanced Tools p.5 Holes/Pockets/Pads not normal to sketch plane p.6 Creating Grooves p.9 Creating Ribs and Slots p.16 Creating Stiffeners p.27 Creating Lofts p32 3D Wireframe p.67 Surface Based Features p.73 Advanced Draft p.80 Thickness p.95 Using Transformations p.97 3D Constraints p.103 Local Axis p.108 Annotation p.116 Analysis p.127

Table of Contents (2/2) Part Management p.137 Measure, Mean Dimensions, Scan, Parents-Children p.138 Cut, Paste, Isolate, Break p.152 Inserting and Managing Bodies p.159 Multi-Model Links p.182 Scaling p.194

Advanced Tools You will learn how to create and use other tools of Sketch-Based, Surface-Based and Dress-up Features. You will also learn tools of Transformations, 3D Constraints, Local Axis and Annotation.

Holes/Pockets/Pads not Normal to Sketch Plane

What are Holes/Pockets/Pads not Normal to Sketch Plane ?

Holes/Pockets/Pads not Normal to Sketch Plane

Creating Grooves

Creating Grooves

Groove : 3d Line axis

Groove : Reverse Side

Additional Information (1/3)

Additional Information (2/3)

Additional Information (3/3)

Creating Ribs and Slots

What is a Rib ?

What is a Slot ?

When Should we Use Ribs and Slots ?

Creating a Simple Rib

Creating a Slot

Additional Information (1/5)

Additional Information (2/5)

Additional Information (3/5)

Additional Information (4/5)

Additional Information (5/5)

Creating Stiffeners

What is a Stiffener ?

When Should we Use Stiffener ?

Creating Stiffeners

Additional Information

Creating Lofts You will learn how to create Lofts and Removed Lofts

Creating Simple Lofts

What is a Loft ?

When Should we Use Lofts and Removed Lofts ?

Loft Creation : Guide Lines

Loft Creation : Spine

Loft Creation : Closing Point and Orientation

Loft Creation : Tangent Surfaces

Remove Lofts

What is Remove Loft Material ?

Remove Loft Material

Remove Loft Material : Closing Point and Orientation

Remove Loft Material : Tangent Surfaces

Coupling

What is Coupling when Creating Loft ?

Coupling when Creating Loft

Coupling when Creating Loft : Ratio

Coupling when Creating Loft : Tangency

Coupling when Creating Loft : Tangency then Curvature

Coupling when Creating Loft : Vertices

Coupling when Creating Loft : Points of Discontinuity

Loft: Manual Coupling (1/2)

Loft: Manual Coupling (2/2)

Manual Coupling: Displaying Uncoupled Points

Loft: Relimitation (1/3)

Loft: Relimitation (2/3)

Loft: Relimitation (3/3)

Changing the Closing Point

What is Changing the Closing Point when Creating Loft ?

Changing the Closing Point when Creating Loft (1/6)

Changing the Closing Point when Creating Loft (2/6)

Changing the Closing Point when Creating Loft (3/6)

Changing the Closing Point when Creating Loft (4/6)

Changing the Closing Point when Creating Loft (5/6)

Changing the Closing Point when Creating Loft (6/6)

3D Wireframe Elements

What are 3D Wireframe Elements ?

Creating 3D Wireframe Point

Creating 3D Wireframe Line

Creating 3D Wireframe Plane

Using 3D Wireframe Elements to Create a 3D Curve

Surface Based Features

What is a Surface Based Feature and when Do You Use It (1/2) ?

What is a Surface Based Feature and when Do You Use It (2/2) ?

Split

Thick Surface

Close Surface

Sew Surface

Advance Draft

What is the Advance Draft Command ? (1/5)

What is the Advance Draft Command ? (2/5)

What is the Advance Draft Command ? (3/5)

What is the Advance Draft Command ? (4/5)

What is the Advance Draft Command ? (5/5)

Advanced Draft Angle: Draft Both Sides (1/9)

Advanced Draft Angle: Draft Both Sides (2/9)

Advanced Draft Angle: Draft Both Sides (3/9)

Advanced Draft Angle: Draft Both Sides (4/9)

Advanced Draft Angle: Draft Both Sides (5/9)

Advanced Draft Angle: Draft Both Sides (6/9)

Advanced Draft Angle: Draft Both Sides (7/9)

Advanced Draft Angle: Draft Both Sides (8/9)

Advanced Draft Angle: Draft Both Sides (9/9)

Thickness

Thickness

Using Transformations

What is Transformation ?

When Should we Use a Transformation ?

Translation

Rotation

Symmetry

3D Constraints

What is a 3D Constraint ?

When Do we Use 3D Constraints ?

Creating 3D Constraints

Using 3D Constraints

Local Axis

What is a Local Axis ?

Local Axis : Creation

Local Axis : Use

Customizing Local Axis (1/3)

Customizing Local Axis (2/3)

Customizing Local Axis (3/3)

Additional Information

Annotation You will learn how to attach a text to a part and how to add hyperlinks to your document and then use them to jump to a variety of locations

Text with Leader

What are Texts with Leader?

Texts with Leader

Additional Information

Flag Note with Leader

What are Flag Notes with Leader?

Flag Notes with Leader (1/2)

Flag Notes with Leader (2/2)

Using Flag Notes with Leader

Additional Information

Analysis You will learn how to analyze part in order to display the threads and tap, and to check if a part can be removed from mold in accordance with its draft angles

Analysing Threads and Taps

What is the Threads and Tap Analysis ?

Analysing Threads and Taps (1/2)

Analysing Threads and Taps (2/2)

Draft Analysis

What is the Draft Analysis ?

Draft Analysis (1/2)

Draft Analysis (2/2)

Additional Information

Part Management You will learn Part Management tools that you will need to design complex parts and integrate these parts into a Multi-model Environment

Measure, Mean Dimensions, Scan, Parents-Children

What is Measuring Elements ?

Measuring Elements

What are Mean Dimensions?

Mean Dimensions (1/4)

Mean Dimensions (2/4)

Mean Dimensions (3/4)

Mean Dimensions (4/4)

What is Scanning a Part ?

Scanning a Part

What is Parents-Children Relationship ?

Parents-Children Relationship

Parents-Children (Edition) (1/2)

Parents-Children (Edition) (2/2)

Cut, Paste, Isolate, Break

What is Cut/Copy and Paste (Drag and Drop) ?

Cut/Copy and Paste (Drag and Drop)

What are Isolate and Break ?

Isolate, Break (1/3)

Isolate, Break (2/3)

Isolate, Break (3/3)

Inserting and Managing Bodies

What is Inserting a Body?

Inserting a Body

What is Inserting and Managing Bodies ?

Assemble

Add

Remove

Intersect

Union Trimming Bodies

Removing Lumps (1/3)

Removing Lumps (2/3)

Removing Lumps (3/3)

Assembling a Set of Bodies (1/3)

Assembling a Set of Bodies (2/3)

Assembling a Set of Bodies (3/3)

What is Replacing a Body?

Replacing a Body (1/3)

Replacing a Body (2/3)

Replacing a Body (3/3)

Change Boolean Type (1/4)

Change Boolean Type (2/4)

Change Boolean Type (3/4)

Change Boolean Type (4/4)

Multi-Model Links

What are Multi-Model Links ?

Establishing Multi-Model Links (1/3)

Establishing Multi-Model Links (2/3)

Establishing Multi-Model Links (3/3)

Sketch Selection with Multi-Documents Links

Sketch Selection with Multi-Documents Links (1/5)

Sketch Selection with Multi-Documents Links (2/5)

Sketch Selection with Multi-Documents Links (3/5)

Sketch Selection with Multi-Documents Links (4/5)

Sketch Selection with Multi-Documents Links (5/5)

Additional Information

Scaling

What is Scaling ?

Scaling/Affinity